Skip to content
Speaker Tester

Water eject · 165 Hz

Speaker Cleaner: Water Eject Sound

Phone sounding muffled after rain, a spill or a swim? Play a 165 Hz tone with the speaker facing down. The cone moves hard at this low pitch and pushes trapped water and loose dust out through the grille.

  • Free
  • No download
  • No sign-up
  • Audio stays on your device

Loading…

165 Hz tone

0:30

Speaker facing down, volume up, then press Eject Water.

Mode
Duration

Why it starts at 60%: a quiet tone can’t move water. It’s a self-help trick, not a repair guarantee.

20%

Before you start. Unplug headphones, hold the phone away from your ear, and stop right away if you hear distortion or rattling.

How a sound can push water out of a speaker

A speaker is a light cone or membrane moved back and forth by a magnet. At low frequencies it has to travel much further to make sound, so a 165 Hz tone makes the membrane pump air in and out of the small chamber behind the grille. Water droplets sitting in the grille mesh get shoved outward with each stroke and, with the phone facing down, gravity carries them away instead of back in.

This is the same idea Apple uses for the Water Lock feature on Apple Watch, which plays a series of tones to clear its speaker after swimming. 165 Hz is a widely used choice because it is low enough to produce big movement but still high enough that a tiny phone speaker can reproduce it. The Sweep mode glides between 60 and 300 Hz so it also hits whatever frequency your particular speaker moves most at, and Pulse mode switches the tone on and off to give the water a series of sharp jolts.

Fix my speaker: what else to try

If the sound is still muffled after a few runs, let the phone dry naturally for a few hours with the speaker facing down in a warm, airy place. Don’t use a hair dryer on high heat, don’t push cotton buds or pins into the grille, and skip the bag of rice: Apple and others advise against it, because rice dust can end up in the ports.

For dust and pocket lint, use a soft, dry toothbrush to brush across the grille, or a little sticky putty pressed gently onto it and lifted away. If the speaker crackles, buzzes at every volume or makes no sound at all, the problem is probably not water. Restart the phone, check that it isn’t stuck in headphone or Bluetooth mode, and run the phone speaker test to see which frequencies are missing.

This tool cannot repair a damaged speaker, and it is not a repair guarantee. Salt water, sugary drinks and long submersion can corrode parts inside; if the phone was fully submerged, back it up and get it checked even if the sound comes back.

Frequently asked questions

How do I get water out of my phone speaker?

Play a low 165 Hz tone at full volume with the speaker facing down, so the vibration pushes droplets out of the grille. Press Eject Water above to play it for 30 seconds, wipe the grille, and repeat two or three times. Then leave the phone to dry in open air for a few hours. Don’t use heat, rice, cotton buds, pins or compressed air, because they can push water or debris further in.

Does a water eject sound really work?

Often, yes, for droplets trapped in the speaker grille after a splash, rain or a swim. It can’t remove water from inside the phone or fix corrosion, so it isn’t a guaranteed repair.

Which mode should I use: tone, sweep or pulse?

Start with the 165 Hz tone. If the sound is still muffled, try Sweep, which covers 60–300 Hz to match your speaker’s strongest movement, then Pulse, which knocks the water with short bursts.

How many times should I run the speaker cleaner?

Two or three 30-second runs are usually enough. Wipe the grille between runs. If nothing changes after that, let the phone dry for a few hours before trying again.

Can the speaker cleaner damage my speaker?

Short runs at full volume are within what phone speakers are designed for, and the built-in limiter prevents clipping. Don’t loop it for long periods, and never hold the phone against your ear while it plays.

Does it work on iPhone, Android and Apple Watch?

It works on any phone, tablet or laptop with a browser. On iPhone turn off the silent switch first, because web audio follows it. Apple Watch has its own Water Lock feature for this.

How do I fix my speaker on my iPhone?

Most iPhone speaker problems are fixed by checking settings and clearing the grille, not by a repair. Turn off Silent mode, raise the volume, disconnect Bluetooth and restart the phone. Take off the case and gently brush the bottom speaker grille with a soft, dry brush, without liquids, pins or compressed air. If water got in, run the water-eject tone above. If the sound is still distorted or crackly, have a repair shop or Apple check it.

How do I clean a phone speaker?

Gently sweep the grille with a soft, dry brush, such as a clean soft toothbrush, with the speaker facing down. Take off the case first and brush across the holes so lint and dust fall out instead of being pushed in. Don’t use liquids, pins, needles or compressed air, which can damage the mesh or the speaker itself. If the sound is still muffled after a splash, run the 165 Hz water-eject tone above.

Keep testing

See All Tests

Want to check everything in one go? Run the full speaker test on the homepage.