A smooth logarithmic sweep across the whole audible range, with the exact frequency on screen as it plays. Mark where sound appears and disappears to map the real range of your speakers, headphones and ears.
Free
No download
No sign-up
Audio stays on your device
Loading…
Live · Web Audio
Sweep
1kHz
20501002005001k2k5k10k20k
Mode
Output
Frequency
Direction
Duration
Press “Mark” (M) when the tone appears and again when it fades out.
Play
Start quiet. Lower your device volume before you press play, then raise it slowly. Test tones are pure and can be louder than music at the same setting.
High volume. Long exposure can damage hearing, and loud sweeps or sub-bass can damage tweeters and small drivers.
Your upper mark reflects both your equipment and your hearing. Young adults often hear up to 17–19 kHz; by 40 many people stop around 14–15 kHz. If several different speakers all seem to stop at the same point, that point is your hearing. Sweep downwards (High → Low) for a more accurate top-end reading, because it’s easier to notice a tone appearing than fading away.
Listen for the sweep getting suddenly louder or quieter. Those are peaks and dips in the speaker or room response. A buzz or rattle at one frequency points to a loose part resonating.
Frequently asked questions
What is a frequency sweep?
A sine tone that glides continuously from one frequency to another. This one is logarithmic, so each octave takes the same time, matching how we perceive pitch. It reveals the range, peaks, dips and resonances of a sound system.
What frequency is best for testing speakers?
No single frequency tests everything, so a sweep from 20 Hz to 20 kHz is the best all-round test. For individual checks, use 40–60 Hz for subwoofers and deep bass, 80 Hz around the subwoofer crossover, 1 kHz to compare levels between speakers and 8–10 kHz for tweeters. Start quietly at every frequency, because high tones sound louder and can damage tweeters. The tone generator plays any single frequency you choose.
What frequency range can humans hear?
About 20 Hz to 20 kHz for young people with healthy hearing. The upper limit falls with age and noise exposure, so most adults hear up to 14–17 kHz.
Why does the sweep get quieter at high frequencies?
Partly your speakers (tweeters roll off above their range), partly your hearing, which is less sensitive above 10 kHz. The sweep itself is generated at a constant level throughout.
Is the sweep accurate above 20 kHz?
The sweep is generated at your device’s sample rate (usually 44.1 or 48 kHz), which can reproduce frequencies up to about 22 kHz. We stop at 20 kHz, the conventional limit of human hearing.
Can high frequencies damage my tweeters?
Sustained loud high tones can overheat tweeters. Keep the volume moderate, avoid holding a fixed tone above 10 kHz at high level, and stop if you hear distortion.
How do I tell if a speaker is blown?
A blown speaker distorts, buzzes or goes silent on notes that a healthy speaker plays cleanly. Play a slow sweep at moderate volume and listen for rattling, scratchy fuzz or sudden drops at certain frequencies. Then compare it with the other speaker of the pair: if one sounds clean and the other doesn’t, the second one is likely damaged. With the grille removed, a torn cone or a loose, crumbling surround confirms it.
What does a blown speaker sound like?
A blown speaker sounds fuzzy, rattly or scratchy, and in the worst case it makes no sound at all. A torn cone or surround tends to flap or buzz on bass notes. A damaged voice coil scrapes or distorts even at low volume. A dead tweeter makes everything sound dull, with no crisp cymbals or “s” sounds. During a sweep, these faults show up at particular frequencies rather than all the time, which helps you tell them apart from a bad recording.
What is the most common speaker failure?
The most common failure is a burnt voice coil caused by too much power, usually from turning up an amplifier until it distorts. Clipping sends harsh, high-frequency energy to the tweeters, which have the thinnest coils, so they often fail first. Other frequent faults are foam surrounds that crumble with age, torn cones, and loose or corroded connections. Keeping the volume below the point where you hear distortion prevents most of them.
Why do my speakers crackle or buzz?
Crackling usually comes from a loose connection, a dirty volume control or interference, while buzzing is often a rattle, a ground loop or a damaged driver. If the noise is there with nothing playing, suspect cables, power or a ground loop, and try another outlet or cable. If it only appears on certain notes, sweep slowly to find the frequency, then check for loose grilles, panels or objects touching the speaker. Distortion even at low volume points to a damaged driver.