Skip to content
Speaker Tester

Device · Soundbar

Soundbar Test

Play this page through your soundbar from a laptop, phone or the TV’s own browser. The sequence checks that the bar’s left, center and right are where they should be, that the subwoofer blends in, and that nothing rattles.

  • Free
  • No download
  • No sign-up
  • Audio stays on your device

Loading…

8 steps · about 57 seconds

Press play to run every test

Left, dialogue, right, polarity, subwoofer blend, range and noise.

  1. 1Left channel4 s · From the left end of the bar (or the left surround if you have one).
  2. 2Center / dialogue4 s · From the middle of the bar, right where the TV picture is.
  3. 3Right channel4 s · From the right end of the bar.
  4. 4In phase4 s · Focused in the center with solid weight.
  5. 5Out of phase4 s · Wide and hollow. Virtual surround processing may make it sound wide too, so compare carefully.
  6. 6Subwoofer sweep 20–200 Hz14 s · A rising tone from the sub, then a smooth handover to the bar around 80–150 Hz with no gap.
  7. 7Full sweep 20 Hz–20 kHz18 s · Even from the sub through the bar’s tweeters.
  8. 8Pink noise5 s · An even hiss with no rattle from the TV stand or wall.
20%

Start quiet. Lower your device volume before you press play, then raise it slowly. Test tones are pure and can be louder than music at the same setting.

Channels and dialogue on a soundbar

A soundbar packs several speakers into one box and uses processing to spread them out. The left and right steps should come clearly from each end of the bar, and the center step should sit in the middle of the TV picture. That is where dialogue lives in films, so if the center step seems to come from one end, voices will too. Check that the bar is centered under the screen and that no wall or cabinet edge is reflecting one side more than the other.

This page plays stereo, so a 5.1 bar will either play these steps from its front speakers or upmix them into virtual surround. If the steps sound oddly wide or phasey, switch the bar to its stereo or standard mode for the test. Surround and height speakers can be checked with the bar’s own built-in test tone menu.

Getting the subwoofer to blend

The subwoofer sweep should rise smoothly and hand over to the bar somewhere between 80 and 150 Hz without a hole or a boomy hump. If the tone dips and then returns, try moving the sub along the front wall, or near the sofa, and run the sweep again; room position matters more than any setting. Lower the sub level if the bottom of the sweep sounds much louder than the top.

Wireless subs occasionally lose their link and fall silent, which is easy to miss in films. If the 20–80 Hz part of the sweep is missing completely, re-pair the subwoofer using the button on its back. Rattles on the sweep usually come from the TV stand, glass doors in the cabinet, or the sub touching furniture.

Frequently asked questions

How do I test my soundbar?

Play this page through the soundbar from a laptop, phone or the TV browser, sit in your usual spot and press Play. Each step tells you where the sound should come from.

Why is soundbar dialogue hard to hear?

The center image may be off, the bar may be in a wide surround mode, or bass may be masking voices. Use the center step to check placement, turn on the bar’s dialogue mode and lower the sub level.

Why is my soundbar subwoofer not working?

Wireless subs can lose their pairing. If the bottom of the sweep is missing, re-pair the sub with the button on its back and make sure the sub level isn’t at minimum.

Can I test 5.1 or Atmos channels here?

This page tests the front stereo pair, center image and subwoofer. For surround and height channels, use the test tone option in your soundbar’s settings menu.

Keep testing

See All Tests

Want to check everything in one go? Run the full speaker test on the homepage.