Skip to content
Speaker Tester

Device · Bluetooth

Bluetooth Speaker Test

Portable Bluetooth speakers hide a lot behind one grille. This sequence shows whether yours really plays stereo, where its bass starts, how far the treble reaches over your connection, and whether the link drops out.

  • Free
  • No download
  • No sign-up
  • Audio stays on your device

Loading…

6 steps · about 44 seconds

Press play to run every test

Stereo or mono, bass, codec treble limit and dropouts, one after another.

  1. 1Left channel4 s · Sound from the left driver only. If both sides play, the speaker is mono or set to party mode.
  2. 2Right channel4 s · Sound from the right driver only. Many single-box speakers mix to mono, so equal sound on both steps is expected.
  3. 3Center4 s · The same as both previous steps together.
  4. 4Bass sweep 30–200 Hz12 s · Note when bass appears. Small speakers often start around 60–100 Hz and may buzz at full volume.
  5. 5Treble sweep 20–4 kHz12 s · A falling high tone. If it only appears late (below ~8 kHz), the codec or call mode is limiting quality.
  6. 6Pink noise8 s · Continuous hiss. Gaps or warbles mean Bluetooth dropouts: move closer or remove obstacles.
20%

Start quiet. Lower your device volume before you press play, then raise it slowly. Test tones are pure and can be louder than music at the same setting.

Is my Bluetooth speaker stereo or mono?

Many compact speakers have two drivers but still play in mono, because the drivers are only a few centimetres apart and stereo would make no audible difference. If the Left and Right steps sound identical and come from the whole box, the speaker is mono or mixing down. That is not a fault. Larger speakers often have a stereo mode in their app, and two identical speakers can usually be paired as a left/right stereo pair, which this test will confirm in seconds.

If your headphones or speaker suddenly sound mono and muffled on a computer, the device has probably switched to the Hands-Free (call) profile because an app opened the microphone. In Windows and macOS sound settings, choose the “Stereo” or “Headphones” output rather than “Hands-Free” or “Headset”.

Codecs, cut-offs and dropouts

Bluetooth compresses audio with a codec. SBC and AAC typically pass audio up to around 16–20 kHz, while call mode (HFP) is limited to about 4 kHz on older links and 8 kHz with wideband speech. On the treble sweep, a tone that only appears below 8–10 kHz is a strong hint that you are in call mode or on a very poor link. Most people over 30 won’t hear the top octave anyway, so compare with the same sweep on wired headphones before blaming the speaker.

The long pink noise step is a dropout detector: noise is continuous, so any gap, warble or metallic swirl is the link struggling. Move the phone closer, keep your body and walls out of the line of sight, and turn off Wi-Fi hotspots or other Bluetooth devices nearby. If small speakers buzz on the bass sweep at full volume, turn off bass boost; the driver is being pushed past its limit.

Frequently asked questions

Why does my Bluetooth speaker sound mono?

Most small speakers are mono by design. If a stereo speaker or headphones sound mono, they have probably switched to the hands-free call profile; select the stereo/media output in your sound settings.

Why does my Bluetooth speaker cut out?

Distance, walls, your body and Wi-Fi interference all weaken the 2.4 GHz link. Use the pink noise step to hear dropouts, then move the phone closer and remove obstacles until it plays smoothly.

How low should a Bluetooth speaker’s bass go?

Pocket speakers usually start around 80–120 Hz, mid-size ones around 50–70 Hz and large party speakers around 40 Hz. The bass sweep shows where yours becomes audible.

Does Bluetooth reduce sound quality?

Slightly. Media codecs like SBC, AAC, aptX and LDAC sound good, but call mode is heavily limited. The treble sweep helps you tell which one you are hearing.

Keep testing

See All Tests

Want to check everything in one go? Run the full speaker test on the homepage.